Будь ласка, використовуйте цей ідентифікатор, щоб цитувати або посилатися на цей матеріал:
http://reposit.nupp.edu.ua/handle/PoltNTU/6685
Повний запис метаданих
Поле DC | Значення | Мова |
---|---|---|
dc.contributor.author | Попов, С.В. | - |
dc.contributor.author | Гнітько, С.М. | - |
dc.contributor.author | Васильєв, А.В. | - |
dc.date.accessioned | 2020-02-22T18:49:01Z | - |
dc.date.available | 2020-02-22T18:49:01Z | - |
dc.date.issued | 2020-01-22 | - |
dc.identifier.uri | http://reposit.pntu.edu.ua/handle/PoltNTU/6685 | - |
dc.description | Popov S.V. Improving the abrasive resistance of a slide frame in a mortar mixer / S.V. Popov, S.M. Gnitko, A.V. Vasyliev // Eastern-European Journal of Enterprise Technologies. Ser. Engineering technological systems. – 2020. – Vol. 1, № 1(103). – P. 6-14. | uk_UA |
dc.description.abstract | A method has been proposed for machining the outer and inner conical surfaces of the wrist pin and insert, which represent a sliding friction pair on the mortar mixer frame. The machining implies the application on the conical surface of parts, preliminary prepared through turning, of a wear-resistant material in the form of a hard alloyed nickel-based powder. It is applied with a special burner with a hopper-dispenser filled with powder. The result of mixing a combustible gas (acetylene and oxygen) in the burner with the powder from the hopper is melting. In the course of implementing a given technological process, by using mathematical modeling methods, we have determined the optimal mode parameters (PG10N-01 powder consumption is 33.5 g/min.; oxygen flow rate is 7.0 l/min; acetylene pressure is 0.043 MPa) for the gas-flame surfacing, which ensured maximum effect, that is, the greatest strength of adhesion (45 MPa) for the surfaced coating. The surfaced coating quality was checked by using a pin method for determining the adhesion strength between the new coating and the base on a tensile testing machine. A series of experimental studies into the enhancement of abrasive resistance of a sliding frame, namely a comparison of the suкfaced coating with other well-known wear-resistant materials such as steel ShKh15, KhVG, were carried out at a specially designed experimental bench. Its structure is based on a vertically drilling desktop machine adjusted to the conditions of a working process that occurs inside the body of a mortar mixer. These include an abrasive medium, and the radial and axial efforts. To determine the axial load on a frame, we have proposed a structure of the hydraulic device, which includes a pressure gauge, a piston, a sleeve, and a ball. The axial load has been found for the most unfavorable conditions of mixer operation. Its value was implemented at an experimental wear bench. In addition, we have performed a series of experimental studies to determine an optimum angle of the cone at the apex of the wrist pin and insert in a conical slide frame for the minimal wear. Using the proposed technique of a gas-flame surfacing could significantly improve the abrasive and corrosion resistance of a slide frame, thereby prolonging the lifespan of a mortar mixer in general, as well as the overhaul cycle for equipment designed to prepare soluble mixtures used for construction. | uk_UA |
dc.description.abstract | Запропонований спосіб обробки зовнішньої та внутрішньої конічних поверхонь цапфи і вставки, що являють собою пару тертя ковзання опори розчинозмішувача. Обробка полягає у тому, що на конічні поверхні деталей, які були попередньо підготовлені точінням, наноситься зносостійкий матеріал у вигляді твердосплавного порошку на основі нікелю. Нанесення відбувається спеціальним пальником із бункером-дозатором, у який засипається порошок. Внаслідок змішування горючого газу (ацетилен та кисень) у пальникові із порошком з бункера, відбувається розплавлення. | - |
dc.language.iso | en | uk_UA |
dc.publisher | Харків : Технологічний центр | uk_UA |
dc.subject | gas-flame surfacing | uk_UA |
dc.subject | abrasive wear | uk_UA |
dc.subject | slide frame | uk_UA |
dc.subject | hard alloyed powder | uk_UA |
dc.subject | technological process | uk_UA |
dc.subject | газополуменеве наплавлення | - |
dc.subject | абразивне зношування | - |
dc.subject | опора ковзання | - |
dc.subject | твердосплавний порошок | - |
dc.subject | технологічний процес | - |
dc.title | Improving the abrasive resistance of a slide frame in a mortar mixer = Підвищення абразивної стійкості опори ковзання розчинозмішувача | uk_UA |
dc.type | Article | uk_UA |
dc.identifier.udc | 667.637.22:620.178.16 | - |
Розташовується у зібраннях: | Секція прикладної механіки (технології машинобудування) кафедри Галузевого машинобудування та мехатроніки |
Файли цього матеріалу:
Файл | Опис | Розмір | Формат | |
---|---|---|---|---|
ABSTRACT AND REFERENCES.pdf | 127.62 kB | Adobe PDF | Переглянути/Відкрити | |
P o p o v.pdf | 2.2 MB | Adobe PDF | Переглянути/Відкрити |
Усі матеріали в архіві електронних ресурсів захищені авторським правом, всі права збережені.